Production n Operations 3

Select The Blank
Question Production control work is ________ in case of floor inspection as compared with the centralised inspection.
Correct Answer easier
Your Answer easier

Multiple Choice Single Answer
Question Following is not an input information for Process Planning
Correct Answer Inventory level
Your Answer Inventory level

Multiple Choice Multiple Answer
Question Which are the three types of float?
Correct Answer Total float , Independent float , Free float
Your Answer Total float , Independent float , Free float

Multiple Choice Single Answer
Question Which of the following tool is used by Industrial Engineering Department for estimating the Performance Standard in case of new jobs?
Correct Answer Tables of synthetic standards
Your Answer Work study

True/False
Question As a general rule, the number of tail event of an activity is more than that of it's head event.
Correct Answer False
Your Answer False

True/False
Question The time chart, if necessary, may be modified considering the limitations of resource.
Correct Answer True
Your Answer True

Multiple Choice Multiple Answer
Question What is the basic minimum requirement for those who are responsible for the quality of design?
Correct Answer In depth knowledge about alternative materials and manufacturing processes , access to latest technology and production process adopted by industries in the developed market , Continuous effort in product development
Your Answer In depth knowledge about alternative materials and manufacturing processes , access to latest technology and production process adopted by industries in the developed market , Continuous effort in product development

Multiple Choice Single Answer
Question Which of the following policies is advisable in case of low product variety and large volumes?
Correct Answer Low Skilled Labour & Special Purpose Machines
Your Answer Low Skilled Labour & Special Purpose Machines

Multiple Choice Single Answer
Question What do you understand by the critical analysis of existing jobs to develop easier and effective method?
Correct Answer Method study
Your Answer Method study

True/False
Question Inspection Order can be a verbal order
Correct Answer True
Your Answer True

Multiple Choice Multiple Answer
Question Which of the following products should be produced by using mass production?
Correct Answer Refrigerator , Tyre for automobile , Television Set
Your Answer Refrigerator , Tyre for automobile , Television Set

True/False
Question Originating process of raw material influence Process Planning
Correct Answer True
Your Answer True

Select The Blank
Question In Gantt Chart, the horizontal lines devide vertical lines into sections which represents ________.
Correct Answer No. of work centres or operations
Your Answer No. of work centres or operations

Multiple Choice Multiple Answer
Question What are uses of diagrams in method study?
Correct Answer Study different plant layouts and select the most optimum one , Study the extent of traffic over the different routes of the plant , Identify the extent of backtracking, cross traffic and obstacles encountered during the movement of material.
Your Answer Study different plant layouts and select the most optimum one , Study the extent of traffic over the different routes of the plant , Identify the extent of backtracking, cross traffic and obstacles encountered during the movement of material.

Multiple Choice Multiple Answer
Question Which of the following are illustrations of inspection?
Correct Answer Physical count of incoming material against the quantity mentioned in delivery challan , A dimensional check with measuring instrument , Visual check of burrs and finish
Your Answer Physical count of incoming material against the quantity mentioned in delivery challan , A dimensional check with measuring instrument , Visual check of burrs and finish

True/False
Question Quality control determines what, when, and how much to inspect while inspection actually conducts examination of goods.
Correct Answer True
Your Answer False

Multiple Choice Multiple Answer
Question Which of the following are examples of attributes?
Correct Answer Cracks , Burrs , Texture
Your Answer Cracks , Hardness , Burrs

Select The Blank
Question The ________ pertain to the climatic conditions which the component , product or material should withstand.
Correct Answer Environmental specifications
Your Answer Environmental specifications

Select The Blank
Question The ________ is a pair of chart consisting of average chart and range chart placed one below another on a piece of graph paper.
Correct Answer X bar-R-chart
Your Answer X bar-R-chart

True/False
Question Inspection should be avoided prior to long run of a manufacturing stage as it becomes duplication of work and cost.
Correct Answer False
Your Answer True

Select The Blank
Question The term ________ emplies the foregone profit due to inability of company to produce.
Correct Answer Opportunity cost
Your Answer Opportunity cost

Multiple Choice Multiple Answer
Question Which of the following are uses of the lubricants?
Correct Answer Retard rate of wear and tear of moving parts , Protect parts from moisture and dust , Keep temperature of bearings within allowable limits
Your Answer Retard rate of wear and tear of moving parts , Protect parts from moisture and dust , Keep temperature of bearings within allowable limits

Multiple Choice Single Answer
Question Need for change in layout can occur due to following reason
Correct Answer introduction of new product
Your Answer increase labour efficiency

True/False
Question Delay in completion of projects result in unwelcome additions to the fixed manufacturing expenses.
Correct Answer True
Your Answer True

Multiple Choice Single Answer
Question Which kind of inspection is followed in case of product layout?
Correct Answer Pilot inspection
Your Answer Pilot inspection

Multiple Choice Single Answer
Question Any premise in which persons are employed for purpose of making any product/s is called
Correct Answer Factory
Your Answer Factory

Multiple Choice Single Answer
Question What do you mean by the study of repetitive short cycle operations which involve quick hand / feet motions?
Correct Answer Micromotion study
Your Answer Operation study

Select The Blank
Question The magnitude of an inherent variability is called ________.
Correct Answer Process capability
Your Answer Process Control

Match The Following
Question Correct Answer Your Answer
Consumption of physical effort Lifting Giving instructions
Information received Taking dictation Taking dictation
Change in physical characteristic Punching Lifting
Addition Assembly Posting a ledger

Multiple Choice Single Answer
Question Which of the following data is unnecessary for scheduling process?
Correct Answer Cost breakup of products
Your Answer Cost breakup of products

Select The Blank
Question ________ in the plan is lost if there are frequent revisions.
Correct Answer Faith
Your Answer Data

Select The Blank
Question Inspection is represented by ________ during recording for method study.
Correct Answer Square
Your Answer Square

Multiple Choice Single Answer
Question The process of changing inputs into outputs thereby adding some value to entity can be defined as
Correct Answer Operation
Your Answer Operation

True/False
Question Inspection should be conducted on all incoming materials, semifinished items, bought out components, subcontract items prior to any operation, assembly.
Correct Answer True
Your Answer True

Multiple Choice Single Answer
Question Which of the following is the most popular technique for Project Production?
Correct Answer PERT & CPM
Your Answer PERT & CPM

Match The Following
Question Correct Answer Your Answer
Draining and refilling of oil reserviors of plunger pump Yearly Yearly
Parts lubricated with oil nipple Daily Daily
Tools and slideways two to three times a day two to three times a day
Table lubrication Weekly Weekly

Select The Blank
Question The ________ is a set of tools and techniques by which products are made to comply with the specifications at minimum cost to the firm.
Correct Answer Quality control system
Your Answer Design system

Select The Blank
Question The________ is a very fine work measurement technique whereby the time required to do a job is synthesized by combining the predetermined times for different elements of the job.
Correct Answer Pre-determined Motion & Time Study
Your Answer Pre-determined Motion & Time Study

True/False
Question Every network does not necessarily have a critical path.
Correct Answer False
Your Answer True

Multiple Choice Multiple Answer
Question Which details are recorded in columns when each square of progress card is split up into columns?
Correct Answer Date , Shift , Quantity produced
Your Answer Date , Shift , Quantity subcontracted

Multiple Choice Single Answer
Question Process type layout is suitable when
Correct Answer there is wide variation in processing time of operations
Your Answer Product is required in huge quantity